A Plaster Slab
In pottery work you will always find a use for any number of flat rectangular slabs in your studio or craft room. Here are detailed instructions on obtain and prepare your plaster, as well as construct and pour your plaster mold.
Instructions
Constructing The Mold
1. Start by making the mold, as the plaster will rapidly begin to set once its been mixed. Form the four pieces of wood into a square frame.
2. Apply wood glue to the points where the pieces meet and stick them together, hold together with firm pressure for a count of twenty.
3. Reinforce and connect the joints by driving nails into the sides. When you finish you should have a wooden square with each side approximately 12 and 3/4 inches long, one inch high, and 3/4 inches deep.
4. Place the square in the center of a clean sheet of glass. Plywood will work as well, but plaster doesn't stick to glass while it will hold onto plywood. If you're using plywood coat both the frame and plywood backer thoroughly with oil or Vaseline. If using glass then only coat the wooden framework with oil or Vaseline. Set it aside for future use.
Preparing The Plaster
5. Understand what you need in making the slabs. There are many different kinds and brands of plaster, but the best type for a potter is the U.S. Gypsum Company's pottery plaster. It comes in 100 pound bags or 250 pound barrels, but much smaller amounts are sold by ceramic supply dealers. Only ever buy as much as you will need for a project, plaster does not keep well unless it can be sealed in a completely airtight container. The correct proportion for mold work is 2 3/4 pounds of plaster to one quart of water.
6. Measure the water first when mixing, and put it in a plastic bucket or mixing bowl. Sprinkle the plaster lightly and slowly into the plaster to prevent it from clumping.
7. Allow it to slake for two minutes. Slaking is letting the plaster body absorb the as much of the water as it can. Not doing this results in dry spots and cracks in your mold.
8. Pour out any water remaining on the top of the mixture once the slaking is complete.
9. Stir the mixture by hand. The stirring should be done in such a way as to agitate the mixture and drive out air bubbles. Do not whip or whisk the mixture. The point is to get air out, not in. A good method of stirring is to put the hand, palm upward, on the bottom of the pail and wiggle the fingers vigorously. Continue to mix for two or three minutes.
10. The plaster should begin to thicken. You can tell its ready when a finger can be drawn over the surface of the mixture and leave a slight trace.
Making The Slab
11. Pour the plaster evenly into the frame when it is ready. The sheet of glass or plywood should be on a table with an absolutely level surface, so that when the plaster flows it will make a layer of even thickness.
12. Bump the table vigorously immediately after pouring to get the plaster to flow into all the corners of the mold. If air bubbles rise to the surface, blow on them to break them.
13. Observe the transition. In a few minutes the plaster will begin to set and the surface will lose its shine. At this point it takes on the consistency of cream cheese. it is passing through its period of elasticity, which potters call the cream cheese state.
14. Watch as it begins to harden, and it will then begin to get warm. This is the period of crystallization. When it is cold to the touch, crystallization is completed and it is safe to remove the wooden frame and lift up the slab.
Related posts
Making a plaster cast of your hand or your child's hand is a fun project that leaves you with a perfect, ghostly hand replica to decorate or display. It makes a great conversation piece. While it...
Plaster molds are a handy tool in mass producing ceramics.Plaster molds are used when you want to produce numerous castings of a single object when crafting ceramics. A mold, depending on the obje...
Pottery plaster can be used in both molds and castings.Artists use potters plaster, also called pottery plaster, in both molding and casting projects, particularly for making slip molds for cerami...
Bust sculpted from plasterPlaster molds form a wide variety of products. The most popular products made with a plaster mold are ceramic home decor items. They are also useful in making industrial...
Plaster of Paris is a form of gypsum. The first uses of plaster date back at least 9,000 years to Anatolia (present-day Turkey) and Syria. The Egyptians used it 5,000 years ago as a mortar for mon...
